Snowboard Boot Buyers Guide 2020


Picking the right snowboard boots can have a huge effect on how you ride and whether you are in pain or not! Here is our guide to getting the right size, the right stiffness and the right lacing on your boot so you can spend your days shredding on the hill in complete control and comfort

How should snowboard boots fit?

Snowboard boots should be a snug fit so that you have maximum support for foot and all your movements are directly transferred into your board. When first trying on a boot your toe should just touch the end of the boot, then when the boot is tightened and you give a little flex from your ankle your toe should just pull back from the end of the boot. It’s also worth bearing in mind that the liners of most decent boots are designed to mold to your feet, meaning that if they are a little too tight to start off with they wil pack out after a couple of days wear.

Do Snowboard boot run big or small?

Snowboard sizing should be the same as your normal shoe size, although it’s a good idea to get your feet measured if you’re not sure or if you’re in between sizes. After working for a few seasons in snowboard rental, I’ve learnt that it’s a common misconception that you should go for a size up from your normal shoe size so that they are more comfortable, but boots that are too big can also lead to problems:

Boots that are too big can cause:

  • Lose of responsiveness from your board
  • Heel lift in the back of the boot
  • Toes banging into the front of the boot
  • Rubbing on the side of your foot
  • Cutting off of circulation if you have to over-lighten your bindings

However, all this doesn’t mean that you should go for the smallest size that you can cram your feet into.

Boots that are too small can cause:

  • Loss of circulation
  • Cramp in to bottom of the foot

When we think of shoe sizes we normally just mean the length of the foot, but getting the width of your snowboard boot right can also be important, especially if you’ve got a really wide or narrow foot. Wide feet will effectively experience all the same problems as boots which are too small. That means cramp and loss of circulation. If you’ve got narrow feet you might feel like your moving around too much in the boot and that your heel is lifting

Parts of a Snowboard Boot

So that’s the sizing taken care of but it doesn’t stop there. But before we go over all the other considerations when buying a pair of boots it would be useful to go over some of the terminology.

Shell – the outer part of the boot
Liner – the inner part of the boot, the boot within the boot
Articulated Cuff – The way the shell of the boot i cut to allow the boot to bend at the ankle without deforming the boot
Inner Lacing harness – the lacing harness attached to the inside of the shell which tightens around the ankle of the inner boot and holds it in place
Backstay – the rubbery strip which runs up the back of the shell and helps stop the boot sliding up against the highback of the binding
Footbed – the removable insole which supports the sole of the foot and slides inside the liner.

Snowboard Boot Lacing Systems

There are generally 3 types of lacing system out there, each one with their own pros and cons

Traditional lacing

 

Just like on your sneakers. Most traditional laced boots com with lockable cleats about halfway up around the ankle so you can really tighten the lower half then lock it off

Pros

  • Everyone knows how to do up laces
  • Easy to replace if they snap
  • Generally cheaper boots
  • Good if you’re going for that old school look

Cons

  • Can come undone
  • Means taking off your glover to do them up
  • Slowest lacing system for getting your boot tight

Speed Lacing System

There are loads of different variations of speed lacing systems across the brands but the general principle is the same. The boot have two different laces , one for the top bottom part of the boot and one for the top with a handle on the end of the lace. You just need to pull on each lace handle to get them tight before locking them off in the cleats and stowing the handle away in its holster.

Pros

  • Quick to get your boots tight
  • Can adjust the top and the bottom of the boot independently
  • Don’t need to take your gloves off to adjust your boots

Cons

  • Extra lace can look a bit messy
  • Hard to repair if the lace snaps

Boa Lacing System

The Boa lacing system replaces traditional laces with a cable which can be tightened by turning a dial. Once you’ve got your boots nice and tight the dial is clicked in and locks off the cable. I’d recommend going for a double Boa system which tightens the top and bottom of the boot independently

Pros

  • Easily adjustable without taking off your gloves
  • Quick to tighten and release
  • Neat system with no excess lacing

Cons

  • Most expensive kind of system
  • Hard to repair if the cable snaps
  • Single Boa system doesn’t offer much adjustability top and bottom

Inner Boot Lacing System

Most entry level come with an integrated lacing system which tightens up the liner but doesn’t hold the liner against the shell. These are fine for beginners but one you start to progress you’ll need some extra hold around the ankle. An inner with a lace harness tightens around the ankle of the inner boot and holds it against the shell. This stops any heel lift between the inner and the shell and is a much better option for more advanced riders. Most boots priced in the mid range and above come with this kind of inner lacing.

Snowboard boot flex

The other main consideration is the flex of the boot. How stiff or soft you want you boots to be can depend on a number of factors such as your riding style, your weight and your ability, and it kind of follows the same pattern as how stiff you want your snowboard to be.

For beginners you want a soft pair of boots so you can easily push into them and get the board to respond at low speeds. More experienced riders who want to go fast tend to go for a stiffer boot which is more stable and soaks up some of the bumps at high speeds.

It doesn’t always follow that the better rider you are the stiffer boot you need. It’s important that you are able to bend the boot at the ankle so that you can push onto the toe edge so lighter riders won’t want to go too stiff even if they rip! For freestyle as well you’ll need a bit of a softer boot as you need to be able to push the board around and tweak out your grabs.

How to break in a pair of snowboard boots

Even if you buy the perfect boots for you which are the right size, the right, width and the right flex you may still find that your feet hurt after the first few hours on the hill. This is why it’s important to take some time to break your boots. Especially if you’re away on a week’s vacation you don’t want to lose any time messing around with your boots.

The best way to break in your new snowboard boots is to just wear them around the house for a few hours. Just the action of walking around will help mould the inner to your foot and smooth out any pressure points. Making sure the boots are good and tight will speed up the process. Some boots come with heat moldable liners, whereby you can speed up the process by warming them up with a hair dryer and slipping your foot in